1 Orient Way,

Rutherford, NJ. 07070

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

1 Orient Way,

Rutherford, NJ. 07070

Weekend Plumber? 13 Plumbing Tricks of the Trade

A few do it yourself plumbing pro-tips to help you succeed and make your life a little easier

More than any other kind of house improvement project, plumbing can drive a DIYer insane. Problems emerge, tasks grow, and frustrations increase. Even pros are not immune. Yet one means to take care of the frustrations and accomplish a successful plumbing task is to allow plenty of time a minimum of twice as much time as you assume the task should take.

 

An additional smart step is to know some tricks of the profession. Here are a few favorites from a local area plumber in [county], [region].

Reheat Solder When You Can't Cut a Pipe-weekend-plumber

Reheat Solder When You Can Not Cut a Pipe

The very best solution to separate a soldered pipeline is to cut it. However in some cases you can not– either because you can not get a cutting device within the space or because cutting might leave the pipeline far too short to make a new connection.

 

The solution is to heat up the joint and remove from the fitting as the solder melts.

 

Have a wet rag available and immediately wipe away the liquified solder before it stiffens. (Wear gloves to avoid burning your fingers!) Sometimes a quick wipe will certainly leave the pipeline all set for a new fitting.

 

Very likely, you’ll need to scour off some excess solder with sandpaper or emery cloth before you can slip on a new fitting.

Replace Metal Drain Lines with Plastic

Replace Metal Drainpipe Lines with PVC

Metal drain lines under sinks look a lot more dependable than plastic. However plastic is better in practically every way. It’s cheaper, easier to set up, and a lot easier to adjust or tighten up if a leakage forms. And unlike metal, plastic will not rust.

 

So when a metal drain leaks, often the smartest step is to replace the entire assembly with plastic.

Loosen Stuck Pipelines with Heat

When a threaded connection will not move, applying heat often works, in particular on old hookups that were sealed with pipeline dope that hardened with time. Be patient. Getting the metal hot sufficient can take a number of minutes.

 

Guard close surface areas with a flame-resistant towel. This technique is for water and waste pipes only, never ever for gas or gas lines.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project.

Piggyback Stubborn Shutoffs

Shutoff valves under sinks and toilets have a rotten integrity record. In some cases they will not shut completely; at times they will not shut period. In either instance, there’s an alternate to changing the shutoff.

 

Many house centers carry “piggyback” shutoff valves that connect to existing shutoffs. Just disconnect the supply line and install the brand-new valve (a new supply line is a great idea, too). If the old shutoff shuts most of the way, you will not even need to turn off the main water valve; simply set a container under the valve to catch the trickle while you do the job.

Fix a Clog in Seconds

Take care of a Clog in Minutes

Before you run a drain snake into a clogged up pipeline or dismantle the trap, there are a few different tricks worth attempting: Frequently, you can tug out a blockage with a flexible-shaft pick-up device, or perhaps a Zip-It jig can also do the trick.

 

Likewise, a wet/dry vacuum cleaner just may suck out the clog.

 

A clogged drain or toilet can be caused by the build-up of hair, soap residue and even foreign objects such as hairpin or cotton swabs. If you have a clogged up sink or toilet, you can utilize a plunger to try unblocking it.

 

Nevertheless, if the clog is too far down the pipes or you are unable to resolve it by yourself, contact a plumber near me. Our pros will clear your blocked drain pipes and, if essential, fix them.

 

Are you having problems with drains in your home? 

Don't Overtighten Supply Lines

Do Not Overtighten Supply Water Lines

It’s tempting to crank supply lines on tight, solely to be safe. However overtightening supply lines is actually riskier than under-tightening. A loosened connection that leaks is easy to tighten up, however overtightening can damage rubber seals and split the threaded nuts.

 

So start this habit: Make the hookups at both ends of the supply line finger-tight, after that give them one more one-eighth to one-quarter turn with pliers. If they drip, snug them up a little more.

Do Not Reuse Supply Water Lines

When you’re changing a toilet or a faucet, you can save a few bucks by reusing the old flexible supply water lines. Yet do not. Plastic deteriorates with time, and even a little drip can cause huge water damage. It’s a small risk, but not one worth taking.

 

A better practice is to buy brand-new lines that are wrapped in braided stainless steel; they’re a lot less likely to burst. Yet even if you already have braided lines that are a number of years old, replace them.

Tips for Utilizing Thread Tape

Tape and dope are just as efficient for sealing pipeline threads. The primary advantage of tape is that it will not smear onto your hands or tools and end up on the rug. Below are some suggestions for tape:

 

  •  Affordable tape functions great, but the thicker stuff (often pink for water, yellow for gas) is much easier to handle and tears more nicely.
  • Unlike dope, the tape is for pipeline threads only. Don’t utilize it on compression or other hookups
  • How many times should you twist around the pipeline? There are no guidelines, but one of the most popular answer from pro plumbers was 3.
  • Always wrap the tape clockwise around the threads. Or else, the tape will certainly unroll as you screw the joint together.

Cut Stubborn Elements

Deterioration and mineral deposits have an amazing power to lock elements together, making them practically impossible to disconnect. Frequently, the most effective solution is to cut the stubborn part.

 

Either slice it off or cut kerfs in the part so you can break it off. A hacksaw blade functions well. Oscillating or rotary tools function perhaps even better.

Choose Caulk, Not Putty

Pick Caulk, Not Putty

In spite of the name, our plumbers never utilize plumber’s putty. It damages some types of plastic and stains surface areas such as natural rock. And also, it is likely to dry out, split and allow leakages.

 

Silicone caulk is a safer, longer-lasting sealer in the majority of areas where you may utilize plumber’s putty.

Dope Everything

Use Dope On Everything

Thread sealer (also known as ‘pipeline dope’) is formulated to seal threads. Yet it’s fantastic for practically any kind of connection, even if the threads do not form the seal. Use it on compression fittings, ground fittings, and rubber seals.

 

Since it’s slippery, it allows hookups to glide together properly for a great seal. And, if you utilize a type that doesn’t harden, disassembly and repair will certainly be much easier years later. Some types of dope harm plastic elements, so check out the label.

Don’t Fight It, Replace It

Don’t Battle It, Replace It

If you feel a groove where the O-rings mate to the spout, the faucet is toast. Don’t waste any more time and energy on O-ring repair work– you’ll never ever get a lasting seal. We highly advise changing the faucet.

 

Get a Better Grip

Get a Better Grip

Use a hex socket and valve grinding compound to avoid stripping the set screw.

 

Squeeze the hex socket deep right into the setscrew with one hand and draw the ratchet handle with the other. After that loosen the setscrew with a quick tugging motion.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project

Proud to Install, Repair, and Service the Following Brands: