Use this fundamental maintenance technique to keep your hot water heater working effectively and dependably.
Hot water heater work hard to supply you with warm showers, clean clothes, and shining pots and pans.
So show your hot water heater some love by following a scheduled maintenance program that will keep it working for its estimated 15-year life-span, and potentially beyond.
Here is what you must do:
Set the thermostat to 120 degrees Fahrenheit. You’ll save approximately 5% on energy bills for every single 10 degrees you lower the temperature, and you’ll also lower the risk of scalding.
Unless otherwise defined in the manual, keep a 2-foot clearance around the device.
- Drain about a quarter of the tank a few times a year to eliminate sediment and debris.
- Shut off the cold water supply, hook up a garden hose to the drain valve, and run the water into a pail till it is clear.
If the water stays hazy, open the water supply valve briefly to stimulate any leftover particles before draining the tank again. This also lowers the system’s sound level.
Check the temperature-pressure relief valve once a year by quickly releasing it two or 3 times. Keep a lookout for small leakages from the valve after the screening.
Analyze the sacrificial anode rod every 3 years by loosening and eliminating the hex head screw.
Change the rod if any of the list below conditions exist:
(A 13-inch zinc-aluminum anode rod costs roughly $16).
- More than 6 inches of core steel wire is visible.
- The rod is only around 1/2 inch thick.
- Calcium has actually been applied to the rod.
- Insulate older units with a fiberglass coat to boost effectiveness, making certain not to come into contact with the flue (newer units are already insulated; consult your owner’s manual to validate).
Insulate the hot and cold water lines as well.
When you leave for a prolonged time period, set the thermostat on gas heaters to “vacation,” which keeps the pilot light lit but does not heat the water.
Some jobs are better left to the pros...
Consult a Pro. Get No-Commitment Estimates For Your Project.
How Frequently Do You Need Water Heater Upkeep?
Water Heater care is essential not only for keeping you warm throughout the cold weather. Hot Water Heating systems that are damaged or faulty can in addition lead to serious burns to you and your family members.
How typically should you do water heater upkeep, and what are the warning signals that anything is bad with your water heating unit?
Let’s go over how frequently you need to carry out water heating unit maintenance.
In general, the life-span of your hot water heater will be in between 8 and twelve years. Of course, a variety of aspects can have an influence on this life-span.
- The positioning of the hot water heater in your home.
- How properly it was set up.
- The make/model of the heating unit itself.
- And even the quality of care you provide will all have a result.
Experts suggest getting your hot water heater emptied out at least once a year for repair work and maintenance. Essentially, this means that your tank must be drained with a hose and after that refilled with clean water.
This helps in the removal of excess dirt from your heater, which, if left untreated, can trigger major damage and obstructions in your system. An inspection and deep cleaning of the hot water heater’s coils, rods, and other parts need to be included in the maintenance.
Signals You May Need Water Heater Upkeep
Now that you have a better idea of how typically you should get your water heater serviced, what should you do next?
It’s time to start paying closer attention to the clues that something isn’t quite right with your heating unit. You need to act at once if you spot any of the following symptoms. After all, a defective hot water heater could burst, posing severe damage to you or your family.
1. You See Leaks
Of course, you’ll realize you require hot water heater maintenance if you see a leakage or a large puddle around your heating unit. Not all indicators of a leakage are as clear.
In general, you need to check for leakages around your hot water heating unit at least once a month. Search for drips, damp floor covering, or perhaps a musty smell around the heating unit.
2. Water Pressure Is Low
Low water pressure is irritating, but it is also a sign that your hot water heater needs to be serviced. This is probably due to the buildup of minerals or other types of dirt.
The pressure could also be low due to a knot in the pipe or faulty setup.
Your hot water heater will make a few random noises that are not alarming. What if you begin to hear a lot of clanging, clicking, or even something that sounds like popping?
It is probably a sign of a more severe problem. Normally, what is taking place is that your heating unit is overheating as it tries to adjust for obstructions in the system.
Not only will this increase your hot water expense, but it might also raise your risk of burns if you enter into touch with the heating unit.
4. Rusty Water
Another alerting clue is that something is wrong with your hot water heater. Analyze the water flowing from your faucets.
- Is the color reddish-brown and rusty?
- Is there an extremely metallic taste to it if you’ve tried to drink it?
- Does your water regularly appear dirty?
If this holds true, you are in urgent need of water heater upkeep.
This is since the pipelines themselves have probably begun to rust. Sometimes, you might be able to address this problem without the assistance of a specialist.
Begin by draining as much hot water as possible from your heating unit. (For your safety, we suggest utilizing a five-gallon container.) If, after the 3rd five-gallon container, you’re still seeing the reddish-brown color?
It means that the concern is with your hot water heater instead of your pipelines.
It is best to look for the assistance of a professional if this is the case. They’ll be able to empty your tank more fully, and they’ll probably check the total condition of your pipelines.
Always rely on the services of a professional when in doubt when it comes to water heating unit maintenance.